Let there be light

Time for the whole box to get some electron flow going through its vanes.

I didn't like the fact that the LCD monitor had an external power supply. Looking at the external power supply, you will notice that the power output of the LCD power supply, provides 12V output with 4.16A.

So I though, let's try using the computer power supply. This way, the monitor and whole box will turn off the second the motherboard shuts off the power supply.

I cut off one of the connectors and just to be sure the wires will hold 4.16A I decide to be safe than sorry and use two yellow lines with two black lines.

OK, enough, I need to turn this whole machine on and see how it looks. For this I called my first born Karen to demonstrate.

Now comes the hardest part - Coloring the table. I need to chose colors and also do a very good job in coloring it.

Controls Panel

Time to build the controls panel. I started with a paper template of the joystick and buttons layout that I got from http://www.slagcoin.com/joystick/layout.html. From there I downloaded the panel I wanted and printed it.

I placed the printout on the controls panel wood plaque and secured it with a staples using a staple gun. After that I started drilling into the wood.

I also added two buttons on left upper corner and right upper corner of the panel for Player 1 Start and Credits button respectively.

I also added two buttons on the sides of the panel, one of the left and one on the right for Power On and Exit Game illuminated buttons. The Power On button color is green and the Exit Game button color is red. I then wired the buttons with the ground wire and power for the illumination.

For the power socket, I used an extender power cable which I cut of one of the sides and connected the Red wire (5V) and black (Ground) to the LED connectors of the illuminated buttons.

I had to test the illumination of the buttons before continuing so, here are the results

 All looks good.
Now for the rest of the wiring of the controls panel. I used CAT-5 cables colored red and green. I used two different colors so I will be able to connect them to the other end easily and find which wire goes to which connector on the I-PAC board.

You can also notice that I added two neon lights on the back of the LCD monitor. I'm sure I will keep them, I managed to find a rather neat led strip in HomeCenter that should do a fine job. I haven't decide what to do with it yet, but I'm sure it will handy later on in the project.

Next, I need to connect everything and fire up the machine and see how it looks.

Do not underestimate the power of the glue

I have decided in the last few weeks to stablize the table by using wood glue. I wasn't sure if the glue is strong, but as it turns out the glue was amazingly strong. The table is now steady as a rock. I also added corner supports to make it more stronger and steadier.

On the sides I added small wood sticks to hold a 20cm width plaque of wood. This plaque of wood will hold the LCD screen. At first I wanted to hold the LCD screen only, later it almost has everything on it. The LCD screens come with a back is ready for wall mounting with four screws for securing it. So I went to a screw shop, showed him the screws I had and asked for longer ones, and mounted the LCD on the plaque of wood. The tricky part was measuring the screws locations on the plaque of wood, after all, they are not located in the center of the screen.
I added on the back of the plaque of wood the motherboard and the I-PAC board and connected everything together while keeping everything tidy and nice. The bunch of cables on the left side of the plaque is the VGA cable. It was too long, so  I wrapped it around the wood.

The hard drive that I used was a Compact Flash memory card with a SATA adapter. I placed it on the other side of the plaque on top of the LCD screen.

Here is how it looks from inside the cabinet. Plenty of space left and I have all the equipment mounted.

Next step is mounting the power supply of the screen.

Woodworking for the first time

Wood, tools and peace of paper with the table breakout. This is what I needed to start working on the arcade coffee table.

To start, I need to start marking the wood legs and the wood pieces that need to be joined with dowels.

After the markings I used a tool that was bought from Joint Genie called the JOBBER for creating dowel joints. It did a fine work as you can see in the following picture. You can also notice the tool.
The result of the joining of the wood was prefect and flushed.

After a little more than 2 hours of work, I managed to finish the outer frame of the table and I took a picture of it with my daughter standing inside it. The first thing my daughter said when she saw the table, that the table needs to be colored and if she can do it. I'll probably have to let her color something, but I know how it will turn out :).

I still don't have another picture, but I also have the bottom of the table screwed and secured.

Parents

Parents have a very important role in our lives. You all know this, but most importantly, you can ask them to use their large place (since all the kids left it, so plenty of empty rooms :)) for creating the project.

My mother agreed to this venture and I even got all the stuff there today.

Today was also a very productive day. I needed to get the wood for the table, so I went to an old (yes, very old) carpenter, which we hired once for a small job at the house, and I asked him for the wood parts. He turned me down. After all, it's not worth his time, or he didn't want to work on it. Still, it was worth the drive, he gave me a name of a wood supplier in Haifa that he might be able to help me. So I got into the car and drove there.

Indeed, he was a wood supplier, but most importantly, he provides even small amount of custom wood cuts. I came prepared with my measurements and asked him for the wood cuts.

Now I have all the wood cuts I need for creating the table, well, except for minor ones that require final measurements.

The cost? No more than 95$ for the whole table. Keep in mind I will need paint and a glass top so I'm not done yet spending money :).

I took the parts to my parents house and strait to the basement. There I had a very old table I once designed that was my work bench.

I'm now almost ready, and I hope tomorrow I will have some free time to go over to my parents house and start building the table. I estimate the building of the table in no more than 3 hours.

Oh, and by the way, the wood parts alone are rather heavy, so I agree with my wife, it will be a problem to use the table as a replacement table for the coffee table we already have in the TV section of the house.

Do we have an agreement?

I wanted to share my thoughts with my wife regarding the table and the colors I will be using, after all, I agreed with my wife that the table will part of the furniture right? Wrong!

My wife is having second thoughts about the table and she even mentioned that I may want to take it to my work place and place it there where I can show-off my project to my friends at work. This is her way of saying: "I've changed my mind, I'm not sure I want it".

I understand her, after all the only problem with the table is that it will be heavy and we need a table that can be moved around several times a day.

We'll see what happens, I'm still going to build it and bring it home, from there we will see where it lands.

For now, I want to share the latest design of the table. I colored each side of the table with a color of the joysticks I bought (red, green, yellow and blue).

You can see that the color of the whole panel for player one is red. You should be able to notice the second player panel which is yellow.

I also placed the design for it in the download page, but you can also click here.






The second player panel has been colored yellow in respect to the typical second player joystick color which is yellow.

I also have created a decomposition of the table and measured the parts to have them prepared by a carpenter.

I decided to take no favors (at the end I will require some :) ) and go with the measures to Home-Center (it's an Israeli version of the Home-Depot) and talk to the carpenter there.
I was out of luck, the carpenter has just resigned, so no help there until they hire a new carpenter.

Luckily, my brother in law (which I truly think is a very talented person - but alas won't have the time to share my project) has a relative whose hobby is carpentry. He gave me his phone number, and I will give him a call soon and let him on the project to understand if I'm missing anything.

It seems that I will not have much time this week to meet him, we are preparing for my second child's birthday (he will be two years old) and won't have any spare time to meet the guy, so I guess it's off for next week.

Wood work is fun

To create this table I will require some basic wood working experience, which I don't have. I started by checking the Internet and it seems that ask.com has most of the answers. I finally decided to buy some basic tools for wood working. For joining wood, I'm going to use the dowel joints.

The table requires some minor touches, but it is good for construction phase.

I still require wood for this, and also some cutting tools which I didn't buy. They are too expensive and I will only use them this time, well, until the next project :).

The wood will be bought from a carpenter and I will ask him to cut all the parts I need and then I will connect them and hopefully I will do a good job ;).

The top of the table is made out of pure glass with a lower black cover-up. The cover-up will be done by a good friend, that will do it for free. I will leave an opening for the LCD screen.

As you can see the idea is that the table is in fact a coffee table with no visual joysticks at all.

When the table is used for games, the front cover will be opened and the control panel will be pulled out as a drawer. on the right side you should notice a red button. This button will be illuminated. There is also another green button on the left side.

The green button is for the power-on and the red is for exiting the game.

There should also be neon lighting, but unfortunately the neon light I bought came smashed and I'm checking how to get a replacement.

It should be a good sight to see the table light up when turned on.